Gp4000 series datasheet

65,536 Colors (No blink)/16,384 Colors (Blink) White LED (User nonreplaceable parts. When replacement is required, contact 16 Levels (Adjusted with the touch panel or the software) 50,000 hrs. or more (continuous operation at 25°C [77 °F] before backlight Japanese: 6,962 (JIS Standards 1 & 2) (including 607 non-kanji characters) ANK: 158 (Korean fonts, Simplified Chinese and Traditional Chinese fonts are Standard font: 8 x 8, 8 x 16, 16 x 16 and 32 x 32 pixel fonts, Stroke font: 6 to 127 pixel fonts, Image font: 8 to 72 pixel fonts Standard font: Width can be expanded up to 8 times. Height can be expanded up FLASH EPROM 16 MB (including a logic program area) FLASH EPROM 132 KB (Equivalent to 15,000 steps) FLASH EPROM 8 MB (Replaceable Lithium battery for backup memory) SRAM 320 KB (Replaceable Lithium battery for backup memory) SRAM 64 KB (Replaceable Lithium battery for backup memory) ±65 sec/month (deviation at room temperature and power is OFF) RS-232C Asynchronous Transmission Data Length: 7 or 8 bit, Parity: none, Odd or Even, Stop Bit: 1 or 2 bit, Data Transmission Speed: 2,400 bps to 115.2 kbps, RS-485 (isolation) Asynchronous Transmission Data Length: 7 or 8 bit Parity: none, Even or Odd Stop Bit: 1 or 2 bit Data Transmission Speed: 2,400 bps to 115.2 kbps, 187.5 kbps (MPI) Connector: D-Sub9 (socket) IEEE802.3i/IEEE802.3u, 10BASE-T/100BASE-TX Connector: Modular jack (RJ- Conforms to USB2.0 (TYPE-A) x 1, Power Supply Voltage: DC 5 V ±5 %, Output Current: 500 mA or less, Communication Distance: 5 m or less Conforms to USB2.0 (mini-B) x 1 Communication Distance: 5 m or less *1: Other font sizes can be set up with the Editor software.
*2: Up to 60,000 steps can be converted in software. However, this reduces application memory capacity (for screen data) by 1 MB*3: Depending on the operating temperature and age of unit, the clock can deviate from -380 to +90 sec/month.
For systems where this level of deviation is a problem, the user should monitor and make adjustments when required.
AC 1,000 V, 20 mA for 1 min (between charging and FG terminals) DC 500 V, 10 MΩ or more (between charging and FG terminals) 10 to 90 % RH (Wet bulb temperature: 39 °C [102.2 °F] or less - no condensation.) 0.1 mg/m³ (10-7 oz/ft³) or less (non-conductive levels) For use in Pollution Degree 2 environment 800 to 1,114 hPa (2,000 m above sea level or less) IEC/EN61131-2 compliant, 5 to 9 Hz Single amplitude 3.5 mm [0.14 in.], 9 to 150 Hz Fixed acceleration: 9.8 m/s², X, Y, Z directions for 10 cycles (approx. 100 min) IEC/EN61131-2 compliant 147 m/s², X, Y, Z directions for 3 times Noise Voltage: 1,000 Vp-p, Pulse Duration: 1 µs, Rise Time: 1 ns (via noise Contact Discharge Method: 6 kV (IEC/EN61000-4-2 Level 3) Functional grounding: Grounding resistance of 100Ω, 2mm² (AWG 14) or thicker wire, or your country's applicable standard. (Same for FG and SG terminals) Equivalent to IP65f NEMA #250 TYPE 4X/13 (on the front panel when properly 0.8 kg [1.8 lb] or less (display unit only) W169.5 x H137 x D59.5 mm [W6.67 x H5.39 x D2.34 in.] W156 x H123.5 mm [W6.14 x H4.86 in.], Panel thickness area: 1.6 to 5 mm [0.06 *1: The front face of the GP unit, installed in a solid panel, has been tested using conditions equivalent to the standards shown in the specification. Even though the GP unit's level of resistance is equivalent to these standards, oils that should have no effect on the GP canpossibly harm the unit. This can occur in areas where either vaporized oils are present, or where low viscosity cutting oils are allowed toadhere to the unit for long periods of time. If the GP's front face protection sheet becomes peeled off, these conditions can lead to theingress of oil into the GP and separate protection measures are suggested. Also, if non-approved oils are present, it may cause deformationor corrosion of the front panel's plastic cover. Therefore, prior to installing the GP unit, be sure to confirm the type of conditions that will bepresent in the GP's operating environment. If the installation gasket is used for a long period of time, or if the unit and its gasket areremoved from the panel, the original level of the protection cannot be guaranteed. To maintain the original protection level, be sure toreplace the installation gasket regularly.
*2: Regarding dimensional tolerance, everything +1/-0 mm [+0.04/-0 in.] and R in angle are below R3 [R0.12 in.].
Pro-face's GP4000 Series website http://www.pro-face.com/product/hmi/gp4000.html Copyright (C) 2011 Digital Electronics Corporation. All rights reserved. Specifications may change without notice.

Source: http://www.proface.com.tw/files/pdf/datasheet/GP4000_datasheet/datashee_GP4303TAD_EN.pdf